PCB Drilling ToolsI needed mini carbide drill bits and a Dremel drill press / workstation or one like it (recommended by one online forum for DIY PCB fabrication).
The cheapest source I found for drill bits was this 50 piece grab bag from Harbor Freight, which took forever to arrive. Still, it contained a number of useful sizes for PCB drilling. The commonly used sizes appear to range from: #71 (0.026" / 0.66 mm) through #56 (0.0465" / 1.18 mm). They work beautifully.
I already had a Craftsman rotary tool and chose the matching Craftsman drill press for $40. Some suggest these hobby drill presses have too much side to side slop and will break drill bits. After drilling hundreds of holes in dozens of boards, I disagree. I believe the mechanism is tight enough and easy enough to use for PCB drilling.
In the picture below, you can see the rotary tool, drill press, drill bits, PCB, and a drilling map I made to tell me what size holes to drill and where.
Selecting Drill BitsNot all holes in the PCB are the same size. Larger power devices like rectifier diodes and regulators use larger holes than, say, tiny capacitors or 1/8W resistors.
If you're new at this, here's a good way to get started. Hole sizes are automatically captured by Eagle based on the components' packages.
After creating your PCB layout, Eagle can generate Gerber and Excellon NC drill files, normally used by a drilling machine. The files needed translating to a human readable format: a drill map like the one below.
Here's an example NC PCB drill file. All the NC codes can be found here.
How do we get from the NC drill file to the pretty map above? For starters, the file defines drill sizes (0.028" and 0.032"), then for each drill size, a list of X,Y coordinates is listed for drilling.
If we translate the NC drill file into a comma-separated file format (.csv), we can use Microsoft Excel and OpenOffice Calc to plot x,y points in a scatter plot that then becomes a map of your PCB's holes.
I wrote a fairly simple perl script (download here) to convert the NC drill file into a .csv. Each set of holes is described by two columns for X coordinates and Y coordinates. And each pair of these columns has a heading with the drill size. The pairs of columns (holes) for each drill size appear left to right.
|After drilling some holes|
Note that your PCB drill map is a mirror image of your PCB!
Quicker PCB DrillingAfter you've done this a few dozen times you can eyeball the PCB pad and determine a reasonable drill size. The quick and dirty approach for selecting drills: use ~.027" bits for small holes like 1/8 watt resistors or small caps, ~0.031" bit for medium like transistors and 1/4 watt resistors, and ~0.038" for big holes like pin headers and 1/2 watt resistors.
Time to DrillPick a drill size (slightly larger is better than too small, like 0.042" for 0.040") locate the holes of that size on your PCB chart printout, map to the actual PCB, and drill away.
Don't do anything dangerous. Use eye protection. Be safe! Your safety is YOUR responsibility.
I was able to pretty easily line up the drill bit with the hole. Set the drill height fairly close to the board to make it easy to line up. Use lots of light, too. The wickedly sharp drills running at high rpm cut through the PCB like butter. I don't tend to drill slowly or linger. It seems to work best drilling the PCB quickly. Half a second at most in a smooth motion. It was far easier than I expected. The right tools make any job easier.
|Tinning the PCB traces|
I slathered plenty of paste flux on the traces and applied a very thin layer of solder to each of the traces as well as the lettering. This prevents the traces from tarnishing.
I recently learned that paste flux can be washed off with mineral spirits, leaving a clean board behind. I use a toothbrush dipped in the stuff.
Niggling DetailsThe pcb mounting holes are too big to drill with any of my mini drills but I decided to drill pilot holes using my biggest bit and then chase those on my larger bench top drill press. I now generally standardize on #4 size holes and have a drill bit that works great for this size.
|The finished board|
I decided to put a "silkscreen" layer on the top of the board using laser print transfer. Do this before you add flux! The results were acceptable and the labels were a big help in swiftly populating the board.
wow thanks a lot that helps so much and answered like all my questionsReplyDelete
hey where did you find the pcb layout from?ReplyDelete
I designed the circuit and circuit board layout using Eagle CAD software.ReplyDelete
For those who are still struggling with it, try my instructable:ReplyDelete