tag:blogger.com,1999:blog-5983110881018172452.post3826977933621795437..comments2023-03-25T02:55:49.760-06:00Comments on Bot Thoughts: Eagle Tips: Jumper WiresMike Shimniokhttp://www.blogger.com/profile/17602015624941667574noreply@blogger.comBlogger11125tag:blogger.com,1999:blog-5983110881018172452.post-6370646470283626822017-07-16T11:20:21.839-06:002017-07-16T11:20:21.839-06:00Been scratching my head how to do top links. But y...Been scratching my head how to do top links. But your method is so easy. Thank you.Anonymoushttps://www.blogger.com/profile/12783278674000392578noreply@blogger.comtag:blogger.com,1999:blog-5983110881018172452.post-15025043242816018012016-05-09T20:56:01.749-06:002016-05-09T20:56:01.749-06:00I have created a couple of two layer boards at hom...I have created a couple of two layer boards at home and I will continue to do so.<br />You can by small metal things that you can push through a drilled via hole and then soldered at both sides, it works great. The only downside is that the pad area needs to be quite large(It may very well be possible to use a much smaller but thus far I have kept to the safe side).Richardhttps://www.blogger.com/profile/08018886938410954894noreply@blogger.comtag:blogger.com,1999:blog-5983110881018172452.post-70813306763725553272016-04-28T18:30:02.624-06:002016-04-28T18:30:02.624-06:00thank you soooo much ;) thank you soooo much ;) Anonymoushttps://www.blogger.com/profile/12069919452752694250noreply@blogger.comtag:blogger.com,1999:blog-5983110881018172452.post-281947876601629082015-04-23T08:25:00.331-06:002015-04-23T08:25:00.331-06:00Thanks a lot shimniok for the help
Thanks a lot shimniok for the help<br />AKKU D GR8https://www.blogger.com/profile/00658781954155888466noreply@blogger.comtag:blogger.com,1999:blog-5983110881018172452.post-13069771545580782462013-05-27T11:30:18.224-06:002013-05-27T11:30:18.224-06:00thanks for this man!thanks for this man!Anonymousnoreply@blogger.comtag:blogger.com,1999:blog-5983110881018172452.post-18529067647229839652013-03-28T04:30:48.063-06:002013-03-28T04:30:48.063-06:00Very Goog Indeed!
Thanks for this nice tip.
I mad...Very Goog Indeed!<br />Thanks for this nice tip.<br /><br />I made my own routs before I read this post, this means I added a pad and a stripe to the pad, but the thin rout line was still there,.<br /><br />This way is much more nice, and You get rid of those last thin routlines as well, and the board will probably pass the "erc" check.<br /><br />Thans from SM7UWRAnonymousnoreply@blogger.comtag:blogger.com,1999:blog-5983110881018172452.post-89835189838032946282011-04-28T12:21:22.578-06:002011-04-28T12:21:22.578-06:00In Eagle, if you add a standard resistor then it&#...In Eagle, if you add a standard resistor then it'd have to be in the schematic or the board/schematic would get out of sync.<br /><br />On the other hand, you could experiment with a custom component that has no schematic symbol and only has SMD pads and just lay it where you want it. I discovered my "Bot Thoughts" logo can be placed directly on the board and not in the schematic. The logo is on the tDocu layer. <br /><br />So if you do your own boards, you could do 'pads' on some innocuous layer like tDocu and then when you do the toner transfer, print the regular bottom (or top) layer + the layer with the 'jumper pads' and then the resulting print out will have both. It's kind of kludgey though.<br /><br />Don't know of any other way but if I find one I will post it.Mike Shimniokhttps://www.blogger.com/profile/17602015624941667574noreply@blogger.comtag:blogger.com,1999:blog-5983110881018172452.post-45480130026261019182011-04-02T17:25:49.960-06:002011-04-02T17:25:49.960-06:00Thanks for the tip! But is there a way to add jump...Thanks for the tip! But is there a way to add jumpers as 0Ohm smd resistors on the bottom layer without ajusting circuit schematics?avrnoobhttps://www.blogger.com/profile/03442239095072309381noreply@blogger.comtag:blogger.com,1999:blog-5983110881018172452.post-47042267796716029682010-11-21T10:29:07.196-07:002010-11-21T10:29:07.196-07:00Thanks man. I was searching around for some time f...Thanks man. I was searching around for some time finding nothing useful and then I read your post. It is a clear concept and useful. Thankspsychoulhttp://psychoul.comnoreply@blogger.comtag:blogger.com,1999:blog-5983110881018172452.post-63586337736303897292010-09-19T08:14:57.257-06:002010-09-19T08:14:57.257-06:00Glad I could be of help, Sunish!Glad I could be of help, Sunish!Mike Shimniokhttps://www.blogger.com/profile/17602015624941667574noreply@blogger.comtag:blogger.com,1999:blog-5983110881018172452.post-72295187294409952342010-09-19T03:31:58.521-06:002010-09-19T03:31:58.521-06:00Thanks for the great post, I was trying various di...Thanks for the great post, I was trying various discussion boards, but this post was clear on how to have jumpers on single sided boards.<br /><br />SunishSunishhttps://www.blogger.com/profile/04392788186814796489noreply@blogger.com